• <strike id="ychzk"></strike>
    <li id="ychzk"></li>

    聯系我們

    聯系我們

    地址:濟南市高新區漢峪金谷A5-2棟

    電話:15066665432

    傳真:0531-88984022

    聯系人:殷經理

    郵箱:jnyygt@126.com

    網址:www.quanzg.com

    新聞資訊

    當前位置: 首頁 - 新聞資訊

    鋼板在后期加工時,會因為翹曲導致切割后變形,造成工件報廢,影響用戶正常使用,同時造成企業經濟損失。分析認為鋼板經熱軋后內部及上下表面存在殘余應力,如果殘余應力沿鋼板寬度和長度方向呈不均勻分布,將會對鋼板截面產生一個力矩,使鋼板在分切后發生翹曲??刂拼胧┦牵?/p>

    When the steel plate is processed in the later period, the deformation will be caused by the warping, which causes the work piece to be scrapped, which affects the normal use of the user and causes the economic loss of the enterprise. It is considered that there is residual stress in the inner and upper surface of the steel plate after hot rolling. If the residual stress is uneven distributed along the width and length of the steel plate, it will produce a torque on the section of the steel plate, causing the steel plate to warp after cutting. The control measures are:

    1、由于采用超快速冷卻,提高了形核率,細化了鐵素體晶粒。保持超快冷狀態到相變點附近停止冷卻,隨后進行冷卻路徑控制,得到優良性能的鋼板。

     濟鋼一級代理商

    1. Due to the use of ultra fast cooling, the nucleation rate was improved and ferrite grain was refined. The super fast cold state is kept near the phase transition point to stop cooling, and then the cooling path is controlled to get the excellent performance steel plate.

    2、冷卻溫度

    2. Cooling temperature

    層流冷卻造成的內應力不均衡問題主要是由3種不均勻冷卻導致: 橫向冷卻嚴重不均勻;厚度方向冷卻不對稱;橫向和厚度方向冷卻不均勻混合。

    The problem of internal stress imbalance caused by laminar cooling is mainly caused by 3 kinds of non-uniform cooling: severe non-uniform cross cooling, asymmetric thickness direction, uneven cooling in transverse direction and thickness direction.

    3、冷矯直

    3. Cold straightening

    矯直能改善鋼板殘余應力分布,當鋼板在橫斷面上有應力分布不均時,可以需要采取彎輥措施以增加局部變形的方法來補償縱向纖維的長短不齊,達到消除波浪彎、均勻化鋼板內應力的目的。

    The straightening plate can improve the residual stress distribution, when the steel plate is uneven stress distribution in cross section, may need to take measures to increase the bending method of local deformation to compensate for the uneven length of longitudinal fibers, to eliminate the wave bending and uniform stress to steel plate.

    本文由 濟鋼一級代理商友情奉獻,更多有關的知識請點擊:http://www.quanzg.com我們將用最先進的技術,最真誠的態度,為您提供最為全面的服務。我們將會陸續向大家奉獻,敬請期待。

    This article is from the first tier agents of Jigang, and more knowledge is available. Please click: http://www.quanzg.com, we will provide you with the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will continue to contribute to you and look forward to it.


    上一篇:鍍鋁鋅彩涂板的設計和選用要點
    下一篇:鋼板樁具有哪些優點?
     
    在線咨詢 在線咨詢
    全國咨詢熱線
    15066665432
    特黄特色高清不卡免费视频